The decoration must depend on the paving acceptanc

2022-07-22
  • Detail

Wood floor is a widely used floor decoration material in the decoration of living rooms and public buildings. As its sales volume soared, complaints also showed an upward trend. Therefore, when doing decoration at home, we must carefully check the decoration quality of the floor and do a good job of acceptance

wood floor is a floor decoration material widely used in the decoration of living rooms and public buildings at present. As its sales volume soared, complaints also showed an upward trend. Therefore, when doing decoration at home, we must carefully check the decoration quality of the floor and do a good job of acceptance

shuaibang design Tongji Yu Run

floor acceptance Yang standard

1. Check whether the color of the floor is consistent. If the color difference is too large, which directly affects the beauty, you can ask for replacement; If the color is too consistent and there is almost no color difference, it depends on whether the patterns on the floor surface are the same. If the patterns are similar, it may be craft wood flooring, rather than the so-called precious wood flooring. At present, some flooring material suppliers use general wood flooring, but stick a layer of precious wood veneer on the surface to shoddy it. It is said to be used to prevent moisture. In fact, they are afraid of being seen that the patterns on the reverse side are inconsistent with those on the front side

2. Check whether there is sound on the floor. Walk back and forth on the floor during acceptance, and step harder. Pay more attention to the acceptance, especially the parts close to the wall and the door opening. If there is a sound, walk repeatedly, determine the specific position of the sound, and make a mark. In this case, demolition and resurfacing can be required. The part with sound is caused by the non-standard operation and unqualified materials used by the construction personnel during the construction process. The nonstandard operation is mainly reflected in the insecure fixation of the ground keel; The unqualified materials are mainly reflected in the fact that the ground keel has not been dried. Some decoration construction units use the ground keel that has not been dried for construction. There are traces of drying on the surface, but it is not dry in fact. The keel with high moisture content will shrink in volume during the natural drying of wood, resulting in looseness

3. Check and accept whether the floor is deformed and warped. The method of acceptance is to use a 2-meter-long ruler, lean against the floor, and the flatness should not be greater than 3 mm. Take several more measurements. If the qualified rate is more than 80%, it will be regarded as qualified, otherwise, it will be unqualified. Sometimes we will find that the floor is partially arched: if it is a solid wood floor, it is because the paving is too tight or the floor is too dry (the moisture content is too low); If it is a composite floor, the quality of the floor is poor. Therefore, floor arching is a serious quality problem

4. Acceptance of skirting line: gap between skirting line and door frame ≤ 2 mm; Spacing between skirting seams ≤ 1 mm; The gap between the skirting line and the floor surface should be within 3 mm to 5 mm; The height difference of the toe line buckle should be ≤ 1 mm

5. Acceptance of door buckle strip: the door buckle strip should be installed directly below the door, and it is appropriate to leave no edges inside and outside after closing the door. The gap between the buckle strip and the bottom of the door is 3 mm — Between 7mm, the door can be opened and closed freely. The installation of the buckle should be firm and stable. You can kick the middle part of the buckle with your foot to check whether the two sides of the buckle are cocked or loose and whether there is any abnormal sound

6. Check and accept whether there are cavities, cracks and scratches on the surface of the floor. It is common that there are moths in the ground keel because it has not been treated. When it is found that there are cavities, the floor has been almost eaten; Cracks and scratches can be seen at a glance. The specification stipulates that the floor gap should not be greater than 0.5mm; Scratches are mainly caused by rough decoration. If they cannot be repaired by waxing, they must be replaced

the material variety and grade of the wooden floor meet the design requirements, and the moisture content should be about 10%. The keel and skid have been treated with anti-corrosion treatment. The wooden keel should be installed firmly and straightly, and the spacing and fixing method should meet the specification requirements. The board surface should be paved firmly without looseness, pasted firmly without hollowing, and the type of glue used should meet the specification requirements

visually check that the surface of the wooden floor is planed and polished, without scars, stubbles and burrs, with clear patterns, the color of the clear oil surface is consistent, the paving direction is correct, the surface joints are tight, the joint positions are staggered, and the surface is clean. The skirting board shall be laid with tight joints, smooth surface, and consistent height and thickness out of the wall. Check with a 2m guiding rule. The ground flatness error is less than 1mm, the gap width is less than 0.3mm, the flatness error of the upper opening of the skirting board is less than 3mm, and the flatness error of the joint is less than 2mm

上海癫痫医院

南京皮肤病医院

北京妇科医院

广州精神医院

Copyright © 2011 JIN SHI